dead center

A short work may be turned without using the dead center, by simply chucking it properly at the spindle of the headstock.

一个短的工作在主轴箱主轴上通过适当简单的卡盘无需使用尾架中心也许就能被转动。

The arrow hit the target dead center.

那支箭正中靶心.

The tribune seats were exquisite-dead center of the track, just meters away from the asphalt.

即席记者席的位置太好了–正好位于跑道中心, 距离跑道只有几米远.

Crisp spiky leaves with somewhat bitter taste. The dead center, being a stationary bearing point, must be lubricated.

脆的长而尖的叶子，有点苦味。由于是固定的支承点，死顶尖必须润滑。

Fred fired without thinking, a full auto burst , dead center of mass.

佛瑞德想也没想就开火了, 整整一梭子, 射向心脏部位.

Turn the piston to the top dead center.

将活塞转到上止点.

the a9 highway, that runs almost dead center through the region, has been repaved, and plans are afoot to expand it to six lanes.

运行几乎死通过该区域的中心，A9高速公路，已重铺，并计划致力于将它扩大到六车道。

Now, probably the form of power that we most readily associated with John Milton involves his position at the dead center of the English literary canon.

我们最容易由约翰·弥尔顿，联想到的力量形式很可能，与他处在英国文学经典的中心位置有关。

The dead center, being a stationary bearing point, must be lubricated.

由于是固定的支承点，死顶尖必须润滑。

The results of calculating and experimenting show that the first and largest slap of impact between the piston and the liner occurs around the top dead center from the nonthrust to the thrust face.

经计算和实验表明：活塞在上止点附近，当活塞由非推力面快速地移向推力面时，对缸套具有较大的冲击能量。

According to the simulation calculation results of piston slapping, we can see that the radical acceleration and tilting angular acceleration of the piston near the top dead center in the combustion stroke are most, so the piston slapping is the most serious.

根据活塞敲击运动仿真计算结果发现活塞在燃烧上止点附近的径向加速度以及绕销轴的摆动加速度最大，从而导致活塞对缸套的敲击也最大。

the bottom dead center profile of high speed press in idling time has been promulgated in the text by comparing with the import equipment.

本文揭示了高速压力机在空载时的下死点波形，并与进口设备进行了对比；

It is necessary to use three position signals when reflect the position of Four Stroke Gasoline Engine's piston in cylinder: Top Dead Center Signal, Compression Stroke Signal, Crankshaft Position Signal.

反映四冲程汽油机的活塞在气缸中的位置时，要用到三个位置信号：上止点信号、压缩行程信号、曲轴转角信号。

Dead center turn bench Clinical nursing care of twin pregnancy with a stillborn foetus

双胎妊娠宫内&胎死亡的临床护理

Haughay suffered severe head injuries and was taken to Valley Medical Center by helicopter, where he was pronounced dead.

Haughay头部受到重创，被直升机送往山谷医疗中心，到达医院后被宣布死亡。

Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.

两个上死点的传感器安装在凸轮轴的后面.

The dead center , being a stationary bearing point, must be lubricated.

由于是固定的支承点, 死顶尖必须润滑.

SCLA are soft competition schemes of the learning algorithms, in which the center vectors are trained based on the k means algorithm, and can remedy the problems of the dead node and the sensitivity to initial weight vectors that the latter algorithms have.

SCLA是RBF网络基于k均值方法训练中心向量的学习算法的软竞争格式，它可以克服后者对初始值敏感和死节点的问题。